# LimeSDR QuickTest Failure

**URL:** <https://discourse.myriadrf.org/t/limesdr-quicktest-failure/6455>\
**Category:** LimeSDR\
**Created:** [24 August 2020 19:43 UTC](https://discourse.myriadrf.org/t/limesdr-quicktest-failure/6455 "2020-08-24T19:43:30Z")\
**Posts on this page:** 3\
**Page:** 1

<div class="post-metadata">

**Author:** ![derefnull](https://avatars.discourse-cdn.com/v4/letter/d/5f8ce5/32.png) [@derefnull](https://discourse.myriadrf.org/u/derefnull)\
**Post date:** [24 August 2020 19:43 UTC](https://discourse.myriadrf.org/t/limesdr-quicktest-failure/6455/1 "2020-08-24T19:43:30Z")

</div>

Hi,

I’m encountering QuickTest failures on my LimeSDR. This test was conducted with RF antennae removed. What are my next steps?

user@debian:~$ LimeQuickTest  
[TESTING STARTED]  
-\>Start time: Mon Aug 24 18:21:02 2020

-\>Device: LimeSDR-USB, media=USB 3.0, module=FX3, addr=1d50:6108, serial=0009062000C40F38, HW=4, GW=2.23  
Serial Number: 0009062000C40F38  
Chip temperature: 62 C

[Clock Network Test]  
-\>FX3 GPIF clock test  
Test results: 23954; 27710; 31466 - PASSED  
-\>Si5351C test  
CLK0: 17554 / 17554 - PASSED  
CLK1: 17554 / 17554 - PASSED  
CLK2: 17554 / 17554 - PASSED  
CLK3: 17554 / 17554 - PASSED  
CLK4: 17554 / 17554 - PASSED  
CLK5: 17554 / 17554 - PASSED  
CLK6: 17554 / 17554 - PASSED  
-\>ADF4002 Test  
Result: 10 - PASSED  
-\>VCTCXO test  
Results : 5112912 (min); 5113038 (max) - PASSED  
-\>Clock Network Test PASSED

[FPGA EEPROM Test]  
-\>Read EEPROM  
-\>Read data: 11 05 0F 11 05 0F 03  
-\>FPGA EEPROM Test PASSED

[LMS7002M Test]  
-\>Perform Registers Test  
-\>External Reset line test  
Reg 0x20: Write value 0xFFFD, Read value 0xFFFD  
Reg 0x20: value after reset 0x0FFFF  
-\>LMS7002M Test PASSED

[RF Loopback Test]  
Note: The test should be run without anything connected to RF ports  
-\>Configure LMS  
SetPllFrequency: error configuring phase  
SetPllFrequency: error configuring phase  
SetPllFrequency: error configuring phase  
SetPllFrequency: error configuring phase  
SetPllFrequency: error configuring phase  
SetPllFrequency: error configuring phase  
SetPllFrequency: error configuring phase  
SetPllFrequency: error configuring phase  
SetPllFrequency: error configuring phase  
SetPllFrequency: error configuring phase  
LML TX phase search FAIL  
Failed to set sample rate  
-\>RF Loopback Test FAILED

=\> Board tests FAILED \<=

Elapsed time: 1.78 seconds

user@debian:~$

---

<div class="post-metadata">

**Author:** ![andrewback](https://avatars.discourse-cdn.com/v4/letter/a/22d042/32.png) [@andrewback](https://discourse.myriadrf.org/u/andrewback)\
**Post date:** [25 August 2020 06:29 UTC](https://discourse.myriadrf.org/t/limesdr-quicktest-failure/6455/2 "2020-08-25T06:29:54Z")

</div>

@Zack, could you take a look and advise, please.

---

<div class="post-metadata">

**Author:** ![Zack](https://yyz2.discourse-cdn.com/flex034/user_avatar/discourse.myriadrf.org/zack/32/89_2.png) [@Zack](https://discourse.myriadrf.org/u/Zack)\
**Post date:** [28 August 2020 06:25 UTC](https://discourse.myriadrf.org/t/limesdr-quicktest-failure/6455/3 "2020-08-28T06:25:21Z")

</div>

Hi @derefnull,

Check with CrowdSupply, if it is possible to RMA.